Camcorder Sealed

Check out the video version of this guide on Howcast.com:

Make a camera stabilizer "> How make a Camcorder Stabilizer

Get more great tips on Howcast.com film production:

title = "Production of cinema "> Film Production

You Will Need

PVC Pipe 1 1 / 2 to 2 1 / 2 "diameter
6 6-inch pieces
2 pieces of 3 inches
4 2 pieces 1/2-inch
And 3 1 1/2-inch pieces
10 45-elbow connectors degree
2 PVC T-connectors
A cross four way connector
A can of PVC cement
A PVC end cap
A drill with a 1/4-inch bit
A 1/4-inch carriage bolt, about 4 "long
1/4-inch nut
A nut 1/4-inch Butterfly
A 1/4-inch washer defense
A camcorder
Black Spray Paint
Grip tape

Step 1: Start building fund

Attach two elbow connectors 45 degrees at each end of a 6-inch Pipe PVC. This will be the bottom of your video camera stabilizer.

Step 2: Place the T-connector

Add a piece of 2 ½ inches PVC pipe open end of each connector and then connect a T-connector to both.

Step 3: Connecting PVC to cross

Moreover, placing two 3-inch pieces of PVC to the opposite ends of the four-way cross connector. Place your elbow on the open end of each 3-inch pieces. This assembly will based on your camera.

Ts Link Step 4: to the elbows

Attach the two assemblies that has been built to date by setting the elbows of two 1 ½ inch PVC pieces and parts into the holes of its inner surface in the T-connectors.

Step 5: Add remaining pieces of PVC pipe

Add the other two 2 ½-inch pieces of PVC pipe to the open holes in each T-connector, and attach elbow connectors to the pipe.

Step 6: Connect the pipes side

Connect a pair of 6 inch PVC pipe to the open ends of the elbow connectors. Connect the elbow to their open ends.

Step 7: Build up

Now build the top of the stabilizer. Connect a pair of elbow connectors at each end of a 6-inch PVC pipe. Then, connect the two remaining 6 unused bits of an inch to the other ends of the elbow connectors.

Step 8: Attach the top piece

Connect the elbow at the top pieces of stabilizing a 6-inch side pieces, which form an octagon and complete their basic structure.

Step 9: Seal with cement

Seal all connections with the brush stabilizer in PVC cement and let dry.

Spray paint in black stabilizer to make it look more smart.

Step 10: Drill in END CAP

Creating the assembly chamber. To begin, drill a hole the size of the bolt through the center of the PVC cover.

Step 11: Bolt Thread in cap

Screw the carriage bolt through the bottom of the CAP which appears in the top of the cover. Screw the nut of the screw until it meets the cap, holding the bolt in place.

Step 12: Connecting PVC to top

Attach the bottom of the lid to the remainder of 1 ½ inch piece of PVC and cement together. Let them dry.

Step 13: Place the wing nut and washer

Screw the wing nut on top of the screw and add the washing machine.

Step 14: Screw on the camcorder

Screw the screw into the hole Tripod bottom of the camcorder and tighten the wing nut.

For easier handling, grip tape applied to both sides of the stabilizer bars.

Step 15: Connect the camera to the mounting platform

Once the camera is fixed to the bolt, attach the mounting assembly to the upper connector cross in the center of his platform of cement and PVC connection. You are ready to start recording, continuous shooting at once!

The first film using a handheld camera rig stabilized – or Steadicam – was the elevation of 1976 David Carradine movie glory.

About the Author:

Article Source: ArticlesBase.com – How To Make a Camcorder Stabilizer

Camcorder Sealed

Share and Enjoy: These icons link to social bookmarking sites where readers can share and discover new web pages.